The difference between solid wood flooring and engineered wood flooring

by origamidon

The difference between solid wood flooring and engineered wood flooring

On first inspection there isn’t any great aesthetic difference between solid wood and engineered wood flooring. However before you rush out and opt for the cheapest wood floor there are a few pros and cons to weigh up for both engineered and solid wood floors.

Construction

Solid wood flooring is milled from the tree to give a solid wood plank which has an uninterrupted wood grain and is solely constructed of one solid section of wood. They are mostly constructed with a tongue and groove format.

Engineered wood floors consist of a top layer of natural hardwood which is stuck to a cross layered section of natural soft or hard wood known as ply wood. The cross layering of the ply enables the plank to be more stable due to the glue used so that when the wood expands width ways the different angles reduce the amount of expansion.

Durability

Solid wood flooring is more durable than engineered as it gains its strength from being one solid piece of wood and can be re-sanded and refinished with different waxes, stains or oils more times then engineered. Though the life of any floor does depend on how well it is looked after with recommended care products.

Engineered wood flooring is still very durable and can only be re-sanded five times as the top hardwood layer cannot withstand more.

Really good maintenance is key to durability as when the right cleaning products are used a wood floor can last a very long time.

Stability

Solid wood floor isn’t considered as stable as engineered due to its seasonal movements, meaning that they are susceptible to expansion and contraction with humidity changes in the home. A small perimeter gap accommodates this movement. Solid wood floor is not generally recommended if underfloor heating is already installed as the heat can cup and warp the boards. It is also not advisable to lay solid wood flooring on concrete, unless a full moisture test has been carried out and it is sealed, as the levels of moisture can also affect the boards.

Engineered wood flooring is more stable and more multi functional then solid wood as it is suitable for laying on underfloor heating, concrete and is compatible with most types of underlay making it a good option for those living in second floor and basement flats.

Installation

Solid wood floor can be stuck down or secret nailed and it is not recommended that they are floated over underlay as the joints are glued down and wouldn’t allow the boards to move with seasonal humidity and moisture.

Engineered wood flooring can be stuck down, nailed and floated. It is versatile but does still require a perimeter gap just to be on the safe side with slight board movements.

Laminate Wood Flooring

by deletem3

Laminate Wood Flooring

Laminate wood flooring is a versatile flooring type that gives the appearance of hardwood flooring. With natural looking designs in durable finish, laminate wood flooring can complement any home or office décor.

Designs and Patterns that Fit Every Interior

Laminate wood flooring is suitable for any room including family room, hallway, kitchen, and bathroom. Designed to withstand in heavy foot traffic areas, it is perfect for families with children and pets. Whatever your interior style – warm, light, energetic, playful, elegant or casual – a wide array of laminate wood flooring styles and colors are available. You can choose from smooth, textured, square edge, hand scraped, bevel edge, narrow plank and other interesting varieties.

Although laminate wood flooring patterns resemble original wood flooring, no solid wood is used in its construction. The realistic wood plank flooring patterns are created through advanced computerized technology. Laminate flooring can be installed on any flooring surface, concrete or wood.

Construction with Authentic Wood Appearance

Laminate wood flooring has a layered structure. The inner core layer is made using a high density, moisture-resistant fiber board. A high resolution image of natural hardwood flooring is glued and attached on the top of the fiber board. The backing layer is made using saturated paper which acts as a moisture barrier. The flooring is then finished with a clear coating to protect from stains and fading.

Laminate wood flooring is available in different installation formats – click-lock, glue down, and floating type. Floating type flooring does not fix directly to the sub floor. The most preferred type is click lock flooring that easily snaps together without glue or nails.

A Popular Flooring Option with Cost-saving Features

Laminate wood flooring enjoys high demand due to its affordability, simple installation, durability and easy maintenance. Most of the flooring manufacturers provide a long-term warranty for laminate floors. Dealers of laminate wood flooring also provide installation and maintenance services.

Find More Laminate Wood Flooring Articles

Solid Wood Flooring in the Home

Solid Wood Flooring in the Home

A solid wood floor can add warm tones and a stunning finish to any room. Constructed with pieces of solid wood they have tongue and groove sides so they can be easily connected together. Each piece has a different grain which combines to form a unique look whenever it is used. There is a huge variety of solid wood floors available with many types of wood species, colours and widths available at hardwood flooring suppliers.

The most popular option is oak wood flooring. Europe and America are both the main consumer and producer of this type of hardwood flooring. Oak is available in various types including red, white and European oak, each with their own hardness, grain and colour characteristics.

A cherry wood floor is another popular choice due to its striking grain markings and solid composition. Like other wood floors it is highly resistant to damage. Over time cherry wood flooring darkens from a pale pink colour to warm dark red tone

Exotic hardwoods can give a room a unique look are now readily available at major hardwood flooring suppliers. They can be found for sale alongside other classic real wood flooring such as maple, oak and ash. Real wood flooring can be purchased in pre-finished or unfinished styles. When laying unfinished wood flooring the product can be recoated many times to increase its life and make it last considerably longer than other flooring options.

When laying solid wood floors, begin with a flat, dry and solid sub floor such as concrete, wood or cork. Carpet is not suitable as a sub base and must be removed. Any deviations in level should be rectified with suitable floor filler. A plastic barrier to stop moisture is recommended for floors that are being installed on concrete or in damp areas. Harwood flooring should also be allowed time to acclimatise before it is set down by leaving it the room for several days. For a bathroom wood floor contact you local flooring supplier for suitable product support.

If you are using a wood floor sub base the solid wood floor should be installed at right angles to the original floorboards to aid strength and stability. An expansion area around the perimeter of the room is also recommended to allow for contractions and expansions throughout the winter and summer months. This expansion gap can be covered with skirting boards or a cover strip.

Solid wood floors are tough and hard wearing and by taking care of them their life can be prolonged. Keep gravel, dirt and grit at bay by using a doormat outside and inside the front door. Regular sweeping and vacuuming will take care of any dirt that does settle on the floor and will reduce scratches and everyday wear and tear. Avoid wearing stiletto heels on solid wood floors and if possible only wear indoor shoes or slippers on its surface.

Nothing comes close to the finish that can be achieved with a solid wood floor. By installing solid wood flooring the value of a home often increases and it can give a home the edge over similar property on the market. Solid wood floors are stain resistant and do not trap dust so are especially good for allergy sufferers. There is a wide range of tones, styles and prices on the market so whether you are looking for a cheap wood floor or the ultimate in hardwood flooring, you are sure to find the right match for your room.

More Solid Wood Flooring Articles

FAQ’s For Solid and Engineered Wood Flooring

by LittleRedCera

FAQ’s For Solid and Engineered Wood Flooring

What is Solid Wood Flooring?

Solid wood is exactly as it sounds, one piece of wood from top to bottom.

What is the difference between Laminate and Real Wood Floors?

Real Wood floors will age and mature with your property, this means that they will mark and dent more easily than a laminate would but this is part of the character of real wood floors and should not be viewed as a fault of the product. The shade of the wood surface will change with exposure to sunlight. Dependant on the species, it will either lighten or darken with age. The shade variation will only go on to a certain level and then cease. Any unexposed surface areas will eventually catch up with the colour differences once exposed.

Depending on the type of Real Wood floor (solid v’s engineered) it can sanded and re lacquered a number of times to prolong the life of the floor.

What is the difference between Solid Wood Flooring and Engineered Wood Flooring?

Each type of flooring has its specific use and choosing one over the other is dictated by your lifestyle and needs. Solid wood should be in a moisture-controlled environment. Solid wood (strip or plank effect) should be nailed down only and requires a wood sub floor. Solid wood can be glued to a variety of sub floor materials.

Engineered wood flooring consists of a multi-plied, cross-stacked backing with a real wood veneer (top layer of a selected species). Engineered wood flooring can be used on grade, above and below grade.

Engineered wood flooring is more dimensionally stable so it can be installed in areas where solid wood is not compatible due to moisture. Engineered wood (strip or plank effect) can be glued down over various sub floor. Some engineered woods (strip and plank ) can be nailed down which require a wood sub floor. Engineered woods can also be layed as a floating floor where the tongue and groove are glued together, but the floor is not anchored to the sub floor.

What is a “Floating Floor”?

Floating flooring is a flooring system laid down over a layer of underlay. So while the individual planks are glued together, the individual planks are not nailed or glued into the permanent floor. Instead, the planks form a system that “floats” over the layer of underlay. The underlay can be laid down over existing floors.

What is the required distance between the walls and the flooring boards?

When gluing a Real Wood to the subfloor an expansion gap of 15mm towards the walls is sufficient. With floating-floor installations for every metre of installation width the flooring requires a distance to the wall of at least 5mm, lengthwise an expansion gap of 15mm is sufficient.

Can I install the flooring using one pack after the other?

No, for a natural, harmonious looking installation is recommended to work with approximately 5 open packs of flooring and sort/choose the boards individually by colour.

How much wastage do I allow for?

Despite our strict sorting criteria and thorough quality control there may be certain material-specific peculiarities that customers come across during the on-site selection and installation process which may need to be cut out. Generally, we recommend adding 5% to the room’s sqm-total for cutting scrap.

Which kind of Real Wood flooring is right for me?

The range of choices is huge. According to personal taste and character of the room you can choose between different wood types, board sizes, surface finishes (lacquer-finish or oil-impregnation), surface structures (Antique, Distressed, Brushed), impressions (Block or Wideplank) and styles.

Does sunlight have any effects on the flooring?

Yes, any kind of wood will change its colour over time. During this process light-coloured wood types are not necessarily going to get lighter, dark wood types however will get darker. Every wood type has a characteristic aging process of its own and will react in its individual way.

What is the maximum load a Real Wood flooring can bear on a single point?

With very large loads (e.g. pianos, aquariums, storage heaters and the like) we always recommend gluing down as the installation method of choice.

Can Engineered Real Wood flooring that has been installed as a floating floor be sanded and resurfaced?

Yes, but be aware that every sanding process will take off about 1mm of the flooring’s wear-layer. Try not to use very heavy sanding machinery as the big weight of these machines may lead to the creation of “sanding waves”

How do I care for my oil-impregnated Real Wood floors?

Use Wood-Floor Soap for regular maintenance cleaning. Use a vacuum cleaner for lacquer-finished floors and damp-wipe only if needed.

Should your Floating Real Wood Flooring be installed under kitchen appliances?

In the kitchen, you should install the flooring under kitchen appliances, but be very careful when you slide the appliances over the floor. We recommend covering the flooring with something such as a spare rug to protect the flooring when you’re moving the appliances.

Are there methods that make it possible for ALL stains to be removed from Real Wood Floors or is it sometimes impossible for some stains to be removed?

Most stains don’t penetrate more than the sanding will remove. However, if you have a severe water stain, you may not be able to remove it.

How much of an irregularity (drop or rise) can there be in an existing sub floor before installing your Real Wood Flooring?

You can have a drop or rise up to 4mm over 2 linear metres.

Do Real Wood Floors increase home value?

Absolutely. Real Woods floors are recognised as one of the highest quality floors available and would increase the value of your home.

I am installing a Radiant Heat Floor System involving poly water tubing set in gypsum concrete that would be my sub-floor. Can your products be used with this type of floor heating system?

This installation is okay as long as the tubes don’t touch the wood. You also would have to use a laminated underlay vapour barrier between the concrete and the floor.

Can your Real Wood Flooring be installed over Linoleum and be used on stairs?

Real Wood flooring can be installed on the stairs, however it can be slippery.

You can install our floating Real Wood flooring over linoleum if the linoleum remains sound and tightly glued to the original sub floor.

Is there a type of Real Wood Flooring (e.g. Maple v’s Oak) that is more durable or longer lasting than another?

There isn’t much difference between Real Wood flooring wood types. The only negative on oak is it’s a rather porous wood, but it is a very hard durable wood, as are maple and beech. White oak is slightly harder than red oak. Your choice will really come down to aesthetics.

My concrete floor has a few low spots in it and I was wondering what to use to solve this problem?

Most building materials suppliers have a concrete levelling product. We suggest levelling any areas that are more than 3/16″ in variation. Make sure you use the underlay with a DPM before installing over concrete.

Do you have to install your Real Wood Flooring under existing cabinets?

Ideally, the Real Wood flooring would go under the cabinets. You can, however, cut around the cabinets if removing the cabinets would cause undue complications. Keep in mind, though, that if you were ever to change the cabinets, you could have a problem if the new cabinets weren’t the same size as the old cabinets.

Is it possible to install a Real Wood as a floating floor over concrete?

Real Wood floor is designed exactly for this kind of application. It requires an underlay with a DPM over the concrete floor. The floating floor system can go directly over that.

If there were a crack in the concrete, would it cause problems with a Floating Floor installation?

We recommend that any cracks in concrete be filled with concrete filler and sealed prior to installation. If it’s just a hairline crack you can simply cover the crack with duct tape. Keep in mind that underlay with a DPM must be installed prior to laying down the floor.

Important note prior to installation:
Relative Humidity should be maintained a 40-55% prior to installation and throughout the life span of the floor.

15mm expansion gap must be maintained around the perimeter of the floor.

Find More Wood Flooring Articles

Versatile Wood Flooring With Click Technology For Easy Installation

by “j-M”

Versatile Wood Flooring With Click Technology For Easy Installation

Wood flooring is becoming increasingly popular amongst homeowners due to its versatility, low maintenance and high quality appearance. Unfortunately, installation can be reasonably difficult; this often puts people off opting for wooden flooring.

For individuals that are new to DIY, this can be particularly daunting, especially if they choose to purchase their new flooring from an online retailer. However, there are specialists that have a solution to this problem, click wood flooring. This innovative product is simply clicked into place with no need for nails or glue.

The click wood flooring that they supply is incredibly easy to install yet it offers the same look and feel as standard wooden flooring. They even provide solid wood click flooring, so customers do not have to compromise on quality.

What’s more, as they are primarily based online they are able to keep costs low, meaning that customers do not have to pay over the odds for their wood flooring. Prices start from just £26.79 m², almost half of the usual retail price.

Wood flooring can add a touch of luxury to any home; it can add a traditional look to new-build homes and enhance the appearance of older properties. Their click wood flooring is available in both lacquered and oiled varieties, and in rustic forest or brown oak.

In addition to click wood flooring these specialists also offer a range of flooring to suit many different styles and budgets including engineered wood flooring, laminate flooring, karndean and solid wood flooring.

If you are looking for a stylish new floor that is relatively hassle free to fit, even if you are a DIY novice, take a look at the wood flooring available from online suppliers, or give them a call to discuss the products that will suit your home best.

Are Childrens Wood Beds The Best Choice?

by Br3nda

Are Childrens Wood Beds The Best Choice?

Shopping for childrens wood beds shouldn’t be taken lightly, a personal touch should be considered when making your final decision. A bed is the most personal furniture in the house, but more special in your child’s bedroom. Childrens wood beds can last much longer than metal beds, and are very easy to maintain, wood furnishings leave a room with a comfortable and calming homey feeling. In addition, children wood beds are fashionable, and sturdy, and inviting to look at.

There is no shortage of variety in childrens wood beds to choose from, some people may ask, why buy a childrens wooden furniture? When comparing wood beds to metal beds, wooden beds are made from natural material, also wooden beds have a calming and warm feeling, unlike the cold feel that emanates from beds constructed of metal.

There are some people who are concerned about buying wooden beds for the reason they feel furniture made from wood production are destroying the natural environment. To answer this concern, the fact is that most beds for children and wooden furniture are constructed with pine wood. Pine is a common wood readily harvested from local sustained forests, and have no ill effect on the environment.

Childrens wood beds give any bedroom a sense of class, especially if the wood is varnished. It doesn’t matter if the childrens wood bed is a twin bed, a single bed or a wooden bunk bed, your children will love it. Bunk beds are hugely popular with kids, children love to play on and around bunk beds, and it becomes a joy to sleep in them. Additionally space can be saved with a childrens wood bunk beds as compared to having two single or twin beds in a room, and also give more room for your children to play.

Childrens are unique furniture, and are normally strong and nice to look at. As the years pass, beds for children are long lasting and may out live metal beds that can rust if not maintained. Not many things look as nice as a varnished piece of wooden furniture, and beds for children can give an alluring feel to a room.

Manufacturers of childrens beds have various designs, they offer accessories like built in drawers into bed frame or into the headboard. Many wood beds designs are creative, as an example is the wooden loft bed, space under the bed can be utilized as a storage space, making more space than a bunk bed.

myspace.com/coldwarkids The second single from robbers & cowards
Video Rating: 4 / 5

More Children’s Beds Articles

How To Fit Solid Wood Flooring

by lyzadanger

How To Fit Solid Wood Flooring

How to fit Solid Wood flooring

It is important to start any flooring installation by firstly planning out the room and deciding where to start. Many rooms offer what at first appear to be very complicated situations to overcome. Don’t worry too much about these, all situations have a solution which are covered in this section, alternatively further information can be found in the handy hints and tips section.

Planning:-

When first presented with a room or area which is to be fitted with Solid wood flooring some key factors will help you to decide where to start your installation. Door ways, shape of room and locations of main window are all factors to take into consideration as well as the subfloor (existing floor which is to be covered with Solid wood floor) here are some rules and suggestions:-

Rules –

When laying Solid wood flooring on top of existing floor boards always lay the planks at 90 degrees to the floor boards

It is important not to end up with a piece of flooring at the end of a row which is less than 5cm in length or to have the last row less than 5cm in width. To avoid this measure the room’s width and length and divide the results by the dimensions of the flooring being installed. It may then be necessary to start the first row with a half plank or even to cut the width down to accommodate the area

An expansion joint will need to be inserted into any floor area which is larger than 8m in length or in width, in effect creating two floor areas

Acclimatise the boards in the room they are to be laid in for a minimum of 48 hours. The room should have a relative humidity of between 45% – 65% and a temperature of between 18C – 20C

Suggestions –

It is generally accepted that the best visual effect when installing Solid wood flooring is to lay the boards in the direction of the light source; so towards the main window (not forgetting rule 1 above)

It is also suggested that the floor should run along the longest wall of the room giving the best overall effect. (again take note of rule 1 above)

When laying a floor across a door way it is best practise to start at this point and work back into the room

Installation guide:-

Once your planning stage is complete it is time to prepare the room starting with the subfloor. It is vital that the subfloor is in optimal condition to allow the new floor to perform as expected and help to maintain its longevity

Subfloor preparation –

The main factors to consider are the smoothness, dryness and overall levelness of the floor. If the subfloor is uneven then the new floor will not last long as the pressure on the joints will cause the boards to separate

For concrete floors make sure that they are dry (it takes approx. 1 day per 1mm of wet concrete to be considered dry enough for a Solid wood floor to be installed). The relative humidity of the floor is also vital it should not exceed 85%

For wooden subfloors, ensure there is no movement in the floor. Any loose floor boards should be nailed or screwed securely in place. WBP (water and boil proof) ply can be used over existing floorboards to provide a suitable subfloor surface

All floors must be smooth and level

Finally all debris must be cleaned and the surface of the subfloor must be free from dust and other contaminants

Installation Techniques:-

There are three main ways to install a Solid Wood floor,

Secret nailing

Gluing directly to the subfloor

Installing the Solid wood onto a self adhesive underlay

All of these methods are perfectly acceptable methods of installation for a domestic application, each method has its benefits and draw backs. It is often the subfloor which will help to determine which installation is best suitable.

Installing the floor planks – Secret nailing –

Secret nailing a wooden floor is a method usually chosen when the existing subfloor is wood or when installing directly to joists. Solid wood flooring should have a minimum thickness of 21mm if it is to be fitted directly to joists.

It is possible to use the secret nail technique when the subfloor is concrete or screed. A damp proof membrane (DPM) needs to be placed over the concrete followed by an 18 – 24mm WBP plywood sheet.

Start the first row by loose laying the boards parallel to the wall allowing a 15mm expansion gap. Begin by resting the fitting wedges up against the wall to give you a 15mm gap. This is vital as the Solid boards will expand and contract after installation and if this gap is not present the floor will lift and buckle in the room. The wedges are removed after installation is complete and the gap is covered with either skirting or beading

At the end of the first row you will undoubtedly need to cut a board to length. A good way to measure the length of the board required is to rotate the loose board by 180 degree (facing upwards) so that the tongue is facing the tongue of the previous row. Rest the board next to the first row then mark and cut the boards to size.

(NB. When cutting Solid flooring ensure that a new blade is used)

Once you are happy with the alignment, ‘face nail’ the boards into the subfloor at intervals of 250-300mm or onto every joist. Face nailing is nailing through the top of the planks into the subfloor, counter sink the nails and fill in the dimples with wood filler.

Depending on the tools used and the width of the flooring installed, it may be necessary to face nail two or three rows before secret nailing can begin.

Continue laying rows of planks down ensuring that you keep the 15mm expansion gap around the perimeter of the room. Stagger the boards so that the end joint of each row is further than 150mm apart (brick bond)

Keeping the nails at a distance of 250 – 300mm, secret nail the planks into the subfloor. Secret nailing is a method where planks are secured through the tongue of the boards at a 45 degree angle and counter sunk to allow the groove of the next board to fit tightly. Mechanical nail guns are the best way to achieve professional results and make installation a lot easier.

The final row can be measured and marked to size using the following technique; firstly place the board to be marked directly on top of the last row laid. Place another plank on top of the loose plank but this time have the top plank pushed up against 15mm wedges against the wall to give you the correct measurement allowing for expansion. (be careful not to move the board to be marked) now draw a line along the edge of the top plank marking the board underneath.

The last few rows will also have to be face nailed as there will not be enough room for secret nailing.

Installing the floor planks – Direct gluing –

Direct gluing is a suitable method of installation when fixing on top of a concrete or screed subfloor. One benefit is that the overall height of the new floor is kep to a minimum as there is no need to install an 18mm WBP plywood base. It is also suitable over existing wood floors which are suitably flat and firm.

The subfloor must be flat, firm and level; if necessary a levelling compound may be used. It is important to remember that all subfloors must be dry.

A liquid damp proof membrane must be laid first and allowed to dry.

Using a suitable wood flooring adhesive apply an even coat to the subfloor. A notched trowel held at between 450 and 900 is the best method for this.

Start the first row by laying the boards parallel to the wall allowing a 15mm expansion gap. Begin by resting the fitting wedges up against the wall to give you a 15mm gap. This is vital as the Solid boards will expand and contract after installation and if this gap is not present the floor will lift and buckle in the room. The wedges are removed after installation is complete and the gap is covered with either skirting or beading

At the end of the first row you will undoubtedly need to cut a board to length. A good way to measure the length of the board required is to rotate the loose board by 180 degree (facing upwards) so that the tongue is facing the tongue of the previous row. Rest the board next to the first row then mark and cut the boards to size.

(NB. When cutting Solid flooring ensure that a new blade is used)

After two rows have been successfully installed weigh them down while the glue sets. Any glue which has seeped through to the surface should be removed immediately.

Continue laying rows of planks down ensuring that you keep the 15mm expansion gap around the perimeter of the room. Stagger the boards so that the end joint of each row is further than 150mm apart (brick bond)

Tension straps may be used to hold rows tightly together whilst the glue sets.

The final row can be measured and marked to size using the following technique; firstly place the board to be marked directly on top of the last row laid. Place another plank on top of the loose plank but this time have the top plank pushed up against 15mm wedges against the wall to give you the correct measurement allowing for expansion. (be careful not to move the board to be marked) now draw a line along the edge of the top plank marking the board underneath.

Installing the floor planks – Self adhesive underlay –

Solid flooring can also be laid as a floating floor using a self adhesive underlay. The boards are adhered directly to the underlay which holds the floor together. This method can be used for all subfloor types (following the rules set out above that subfloors be flat, firm and dry) the benefits of the self adhesive underlay is that the room can be used immediately with no drying time required for glue to set.

Lay the underlay at 90 degrees to the direction of the boards ensuring that there are no gaps between sheets but equally important is that the underlay does not overlap. When using the underlay over concrete, first lay a DPM with the edges overlapped by 20cm.

Peel back the foil from the underlay by the width of 2 ½ planks and fold over.

Using the supplied spare foil, lay this over the exposed adhesive surface of the underlay with enough surplus foil facing the wall to fold back over the top of the underlay

Place the fitting wedges up against the wall to give you a 15mm gap. This is vital as the Solid boards will expand and contract after installation and if this gap is not present the floor will lift and buckle in the room. The wedges are removed after installation is complete and the gap is covered with either skirting or beading

Position the first row along the wall and wedges allowing for the expansion gap and ensure that this is perfectly straight. (if the first row is not perfectly straight the entire floor will be ruined) At the end of the first row you will undoubtedly need to cut a board to length. A good way to measure the length of the board required is to rotate the loose board by 180 degree (facing upwards) so that the tongue is facing the tongue of the previous row. Rest the board next to the first row then mark and cut the boards to size

(NB. When cutting Solid flooring ensure that a new blade is used)

Now lay a second row, this will help to stabilise the two rows whilst the foil is removed as well as help to provide a straight line

Once you are satisfied the rows are straight and tightly fitted, peel back the loose foil sheet which will expose the adhesive underlay to the solid wood flooring thus holding the boars in place.

The loose foil may now be discarded. The remaining attached foil will be your work area where new rows will be rested on until you are happy that they are tightly fitted.

Continue to fit the rows down and peel away the foil to fix the boards into place.

The final row can be measured and marked to size using the following technique; firstly place the board to be marked directly on top of the last row laid. Place another plank on top of the loose plank but this time have the top plank pushed up against 15mm wedges against the wall to give you the correct measurement allowing for expansion. (be careful not to move the board to be marked) now draw a line along the edge of the top plank marking the board underneath.

Obstacles –

There are various obstacles you will come across when installing any flooring. The trick is to identify these at the beginning and plan when to tackle them. You do not want to end up at an obstacle where you may need to remove some flooring you have already installed to enable you to deal with the situation.

Door frames are inevitable as almost all rooms will have these. It is necessary to remove a section of architrave and door jam to allow the Solid to be fitted under them, thus hiding the expansion gap away from sight. To do this you will need to place a piece of underlay and an upturned board against the door frame. Using a long saw pressed against the Solid floor begin to cut into the door frame. Make your cut until you reach the wall behind the door frame. Do not worry about cutting into the skirting as the beading will cover this. Remove as much of the door frame as possible so as to allow the right expansion room for the Engineered.

Measure and mark the Solid to fit and then install. When faced with a room where there are doors on both sides of a room and the Solid is installed across the door way it may be necessary to use glue to fit a board at one of these doors. As it is impossible to install the board at 30 degrees and still slide it under the architrave you will need to remove some of the locking joint on the previous row.

Remove the lip along the tongue of the long edge using a sharp chisel. Apply glue to this edge. Slide the board to be fitted under the door architrave and then pull it back into place along the previous row.

Radiator pipe covers can either protrude through the floor or from the wall. If they are floor mounted then the Solid will need to be cut around the pipes with an expansion gap. Measure and mark the position of the pipes on the Solid board and cut the holes out using a 32mm spade drill bit. This should allow for the 15mm pipe and an expansion gap. Then remove the excess Solid to allow the board to be placed against the pipes. The area of Solid removed should represent a keyhole shape. Keep the off cuts of the Solid as these can be glued back into place once the plank is installed.

This short video shows how to install solid wood flooring onto a concrete base using Rewmar MS Polymer flexible adhesive. This adhesive is so easy to use and contains no solvents. Perfect for sticking down both solid hardwood flooring and engineered hardwood flooring. For more information please vist the website www.rewmar.co.uk This product can be bought online from: www.wood2u.co.uk

Find More Solid Wood Flooring Articles

The Basics of Engineered Wood Flooring

by sneakymoose

The Basics of Engineered Wood Flooring

Engineered Wood Flooring is somewhat different from Natural Wood Flooring. Natural Wood Flooring is made from natural wood obtained from different types of trees like Bamboo, Beech, Cherry, Maple, Oak, etc. Engineered Wood Flooring, on the other hand, is part Natural Wood and part Plywood. It is made by using 1/16″ to 1/8″ of finish wood on top and unfinished plywood underneath. So what is inside does not matter, the top surface is100 percent genuine wood. Engineered Wood Flooring is the latest trend in the market and is an innovative and interesting substitute of Natural wood Flooring. Natural Wood Flooring is prone to warping, discoloring and cracking when exposed to extreme temperatures, whereas Engineered Wood Flooring is durable and easier to maintain.

The construction process of Engineered Wood Flooring is different from that of Natural Wood Flooring. In Engineered Wood Flooring, a thin layer of hard wood is laid on top of a thick layer of plywood. The top layer is suited to be walked upon as soon as it is laid down as it has already been polished. The top layer is real wood hence it needs to be polished regularly so that it does not lose its luster. There are different species of Engineered Wood Flooring. A few of them would be:

Hickory Wood- Hand scraped wood gives your home a timeless feeling.
Maple Wood- Maple Wood gives an elegant finish to whichever room it is applied in. It is most suitable in living rooms and dining rooms.
Bamboo Wood- Almost all Bamboo Wood Flooring is engineered but it “Green” and cheap.
Oak Wood- Oak Wood is reddish in color and is inexpensive and the most popular type of wood used for flooring.

Engineered Wood Flooring can be sanded if it develops scratches or dings. There are various disadvantages of Engineered Wood Flooring as well. First and foremost, if the sanding of this floor is not done by a professional, then the life of this floor can get drastically reduced. The sanding of Engineered Wood Flooring should always be carried out by an expert. Secondly, Engineered Wood flooring cannot be sanded more than 2-3 times. If it is sanded excessively, it tends to lose its luster and sturdiness.

Engineered Wood Flooring is moisture resistant and can be suitably applied in areas with maximum moisture like kitchens, basements, bathrooms, etc. Though it can retain moisture well, it is advisable not to use Engineered Wood Flooring in basements that tend to flood frequently or in children’s bathrooms as they are also prone to flooding.

Engineered Wood Flooring has many advantages over Natural Wood Flooring and Synthetic Wood Flooring. If you want sturdy durable flooring that offers the same feel and luster as Natural Wood Flooring and which is inexpensive and durable, then Engineered Wood Flooring is the one to choose.

Related Engineered Wood Flooring Articles

Why Choose Engineered Wood Flooring?

by bsabarnowl

Why Choose Engineered Wood Flooring?

Engineered wood flooring comprises of multiple layers of wood, capped by a veneer of solid wood, which often varies in thickness, averaging around 5mm, but often exceeding 10mm depending on the quality of the product. The top layer is the part visible to the consumer, providing the look and feel to the engineered wood flooring solution. The various layers are secured together with special wood glue, resistant to deterioration and moisture damage.

There are a number of advantages to be found when choosing engineered wood flooring over, for example, solid wood; one of which being the fact that it is often considered more universal by nature, being suitable for installation on top of many different types of surface, including often tricky concrete floors. In addition, it is also considered more flexible and easier to install and maintain than many alternatives, due to being typically sold in easy-to-fit systems, and often coming pre-finished in the pack – meaning no further preparation such as waxing or oiling of the wood needs to take place. This not only cuts down on extra costs for finishing products, but also means that your flooring is ready to go, straight out of the box, saving you or your re-fitter costly additional labour time. Don’t forget however that this type of flooring is not suitable for installation in bathrooms or utility areas, where regular exposure to high levels of moisture may cause movement between the boards to occur.

Is engineered wood flooring durable? The simple answer is yes; and the better you care for the floor, the longer it is likely to last. Maintenance on engineered wood flooring is simple to carry out, and can be as easy as applying a quality laminate and wood cleaner ever so often. These specialist cleaners are neutral detergents that form a self-polishing film, highly resistant to wear and dirt that helps to both clean and protect the product. More intensive maintenance can also involve sanding down the surface or damaged parts of the wood. Bear in mind that there are only a limited number of times that manufacturer’s will recommend sanding down your engineered wood flooring. Typically, a professional sanding machine will remove anything from 0.25mm – 1mm off the top layer of the wood, and for the varieties of engineered wood that feature thinner veneer layers, this must be done rarely and with caution.

The durability of engineered wood flooring also depends very much on the already mentioned thickness of the top layer, which can vary considerably. Generally speaking, a better quality board will feature a thicker veneer layer, giving the product a thicker ‘sandable area’ also; however, the type and quality of the wood also plays and important role, as do the number ply’s in the core. Again, with regard to the number of ply’s, a better quality board will typically comprise of more ply’s than a cheaper one, and the range varies from lower-end products offering 3-ply construction, to the top end boards featuring up to 9-ply’s.

Another important benefit to recognise when deciding whether choose engineered wood flooring over solid wood flooring is that they are suitable for use on top of increasingly popular underfloor heating systems. Solid wood is not appropriate for use with underfloor heating as many varieties of wood are considered unstable when being subjected to significant changes in temperature, and are likely to expand and contract more, causing movement in your flooring to occur. Engineered wood flooring doesn’t suffer from this problem since it’s a composite product and doesn’t react in the same way to temperature changes. This again adds more fuel to the view that engineered wood flooring is more versatile and better value for money than some of its alternatives.

Find More Sold Wood Floors Articles

Importance of Solid Wood Flooring

by kylegordon

Importance of Solid Wood Flooring

Importance of Solid Wood Flooring

Free Online Articles Directory

Why Submit Articles?
Top Authors
Top Articles
FAQ
AB Answers

Publish Article

0 && $.browser.msie ) {
var ie_version = parseInt($.browser.version);
if(ie_version Hello Guest
Login

Login via

Register
Hello
My Home
Sign Out

Email

Password


Remember me?
Lost Password?

Home Page > Business > Importance of Solid Wood Flooring

Importance of Solid Wood Flooring

Edit Article |

Posted: Dec 12, 2008 |Comments: 0

|

Share

Ask a question

Ask our experts your Business related questions here…200 Characters left

Related Questions

How long does wood floor need to acclimate ?
I used a flea bomb but still have found live fleas within 1-2 meters of where i set the bomb off on the wood flooring, should they have died or does take abit of time to kill them off?
I used a flea bomb followed the instructions but i still have live fleas within 1-2 meters of where i let the bomb off on my wood flooring, should they all have died all will it take a while?
I have a fully comprehensive motor policy in the UK my engine set on fire insurance company says this was an electrical fault and is therefore not covered can this be legal

Syndicate this Article

Copy to clipboard

Importance of Solid Wood Flooring

By: Kishore

About the Author

Miles is a well-known author who writes on topics related to Solid Wood flooring, Laminate wood Flooring, Engineered Wood Flooring, information on Wood Flooring Company for the site www.forestfloorsuk.co.uk

(ArticlesBase SC #681124)

Article Source: http://www.articlesbase.com/ – Importance of Solid Wood Flooring

Experience a new classy touch and elegant looks with the solid wood flooring. The solid wood flooring really adds aesthetics and elegance to a room. Let the attractive Solid Wood Floors bring beauty to the every corner of home.  Solid Wood floorings are costly but it increases the ambience of the house, making it worthwhile. They bring warmth, comfort and liveliness to every room, and are lasting for long periods of time. You can buy solid Wood Flooring from any Wood Flooring company in UK.

Wood Flooring Company in UK offers Solid Wood flooring in different appearances and a lot of choices to meet your flooring needs. Wood Flooring Company in UK offers a fantastic range of top quality Solid Wood Flooring across a varied price range. You can also buy Solid Wood Flooring online. Solid Wood flooring companies in UK makes it easier for you to purchase Solid Wood Floors. Solid Wood Floors are wonderful flooring option for the bedrooms and the living rooms.

Go for the Solid Wood Flooring and experience a whole new look of class and sophistication at an affordable price. You will love walking bare feet on the Solid Wood Floors. Solid Wood Floor ensures warmth and everlasting natural beauty. Another benefit of Solid Wood flooring is that they make room more spacious.

Solid Wood Floor gives a brilliant chance for customization. You can find Solid wood floorings at almost all places. Once you install a Solid Wood Flooring, you will automatically feel the supreme beauty. These days parquet, plank boards and strip flooring are popular choices in Solid Wood Flooring category. Solid Wood Floors are best and at the same time simple to maintain. Whether you choose dark coloured or light shade, the Solid Wood Flooring lasts forever. Solid Wood Floor promises a real investment into your home. Select from wide range of the superior quality Solid Wood Flooring for your home from Wood flooring companies in UK.

We offer a range of wood flooring, bamboo flooring, engineered flooring, flooring installation services at Forest Floors UK at best affordable prices. For more information on wood flooring Products and accessories visit us at www.forestfloorsuk.co.uk.

Retrieved from “http://www.articlesbase.com/business-articles/importance-of-solid-wood-flooring-681124.html”

(ArticlesBase SC #681124)

Kishore -
About the Author:

Miles is a well-known author who writes on topics related to Solid Wood flooring, Laminate wood Flooring, Engineered Wood Flooring, information on Wood Flooring Company for the site www.forestfloorsuk.co.uk

Rate this Article

1
2
3
4
5

vote(s)
0 vote(s)

Feedback
RSS
Print
Email
Re-Publish

Source:  http://www.articlesbase.com/business-articles/importance-of-solid-wood-flooring-681124.html

Article Tags:
solid wood flooring, solid wood flooring uk, solid wood floors, wood flooring company uk

Related Videos

Related Articles

Latest Business Articles
More from Kishore

How to Pick Wood Flooring

Here are tips to help you pick the right wood flooring for your home. (01:00)

How to Install an Engineered Wood Flooring

Marc Bartolomeo explains how to install an engineered hardwood floor. (03:19)

Installing Southern Pine Wood Flooring

Southern Pine floors have been used extensively since colonial times for in homes or in schools, churches and in commercial buildings.
(04:18)

Ceramic Tile on Wood Floor

Tim Carter, of http://www.askthebuilder.com, demonstrates tips you should know before installing ceramic tile over plywood or OSB. (01:45)

Removing Stains from Wood Floors

Hardwood floors are beautiful, attractive additions to any home. In short, they are great. The only problem with them is that any stain or damage to them can be expensive to fix, and that is not great. Here is how you can get rid of those stains without s (01:33)

Flooring Company Oxford, Supplying Engineered Wood Flooring At Competitive Prices

There is a flooring company Oxford that offers a wide range of options, from solid wood flooring to engineered wood flooring. Available in a wide variety of wood species, colours and finishes their products suit a variety of budgets.

By:
Danielle Ingraml

Home Improvement>
Interior Designl
Nov 13, 2009

China Bamboo Flooring Review

This is an article reviewing China bamboo flooring. It introduces the history of China bamboo flooring and the problems which China bamboo flooring industry experiences now.

By:
laminateexperterl

Home Improvement>
Constructionl
Feb 07, 2010

Eco Friendly Solid Wood Flooring

Wooden flooring has always been in fashion and gives a royal touch to the place.

By:
Shristy Chandranl

Home Improvement>
Interior Designl
Aug 09, 2010

Wood Flooring And Varnish

So you have decided to install a wooden floor in your home but wonder what sort of finish would you like to give it.This article gives you an overview of the finishes available on the marlet.

By:
Neo Opticl

Home Improvement>
Interior Designl
May 20, 2010

Tree Types And Wooden Floors

Wooden floors can be made of many different types of wood. This article talks about wood types and their properties.

By:
Neo Opticl

Home Improvement>
Interior Designl
May 20, 2010

Transform A Flat Into A Loft Apartment

This article gives you some hints as to how you can restyle any flat into a trendy loft apartment without having to make many changes.

By:
Neo Opticl

Home Improvement>
Interior Designl
Apr 15, 2010

The Texas Chain Saw Massacre

Plot Sally Hardesty (Marilyn Burns) and her brother Franklin (Paul A. Partain) travel with three friends to a cemetery holding the grave of Hardestys’ grandfather

By:
dpdpl

Business>
Human Resourcesl
Jul 23, 2010
lViews: 152

Corporate Fax Plans – Can They Really Save Your Company Money?

Most companies are looking for ways to cut operating expenses, that’s why they should consider a corporate online fax plan. These custom designed fax plans can really save your company money – read this article to find out how.

By:
Titus Hoskinsl
Businessl
Nov 09, 2010

Audible warning devices for the car: train horn kits

MaximusHornSystems.com is the source for all train horn kits. We sell a wide variety train horns, air tank kits, air compressors, gauges, valves, hoses and more at affordable prices.

By:
Ravi Srivastaval
Businessl
Nov 09, 2010

Office Furniture and The Successful Business

Although often forgotten during every day business running, office furniture can play a major role in the positive projection of any company

By:
Andrew Spencerl
Businessl
Nov 09, 2010

Bank of America discounts claims of mortgage repurchases

Bank of America had already made it clear that it will not be buying bad loans from its investors who have been claiming that BOA had improperly handled and facilitated these loans.

By:
rudsontrenl
Businessl
Nov 09, 2010

Tips On Best Diet Burning Fat

With so many Americans overweight, and so much money being spent on the diet industry, it is obvious that not all diets can help you to lose weight. If all methods of diets worked, everyone would have lost weight and stay thin. However, this is not the case. Therefore, some methods are better than others. Here is a general overview of the best ways to burn fat, and the best diet burning fat.

By:
SharonStenning097l
Businessl
Nov 09, 2010

Jobs Jobs Jobs

One of the main purposes of getting a good education is for us to be able to develop certain skills which will help us find a perfect job.

By:
Currencies Directl
Businessl
Nov 09, 2010

How Does A Tankless Water Heater Work?

Many a homeowner looking to save money on energy costs has looked into using different methods of water heating to shave a few dollars of their utility bill.

By:
Nick Messel
Businessl
Nov 09, 2010

Government offering amenities to minorities: Minority Grant

Do you belong to a minority group like African American, Hispanics, American Indians or handicapped? If that’s the case, then you must be at higher risk of having financial difficulties.

By:
Currencies Directl
Businessl
Nov 09, 2010

Importance of Solid Wood Flooring

Wood Flooring Company in UK offers Solid Wood flooring in different appearances and a lot of choices to meet your flooring needs. Wood Flooring Company in UK offers a fantastic range of top quality Solid Wood Flooring across a varied price range.

By:
Kishorel
Businessl
Dec 12, 2008

Add new Comment

Your Name: *

Your Email:

Comment Body: *

 
‘);]]>
Verification code:*

* Required fields

Submit

Your Articles Here
It’s Free and easy

Sign Up Today

Author Navigation

My Home
Publish Article
View/Edit Articles
View/Edit Q&A
Edit your Account
Manage Authors
Statistics Page
Personal RSS Builder

My Home
Edit your Account
Update Profile
View/Edit Q&A
Publish Article
Author Box

Kishore has 1 articles online

Contact Author

Subscribe to RSS

Print article

Send to friend

Re-Publish article

Articles Categories
All Categories

Advertising
Arts & Entertainment
Automotive
Beauty
Business
Careers
Computers
Education
Finance
Food and Beverage
Health
Hobbies
Home and Family
Home Improvement
Internet
Judaism
Law
Marketing
News and Society
Relationships
Self Improvement
Shopping
Spirituality
Sports and Fitness
Technology
Travel
Writing

Business

Agriculture
Ask an Expert
Business Ideas
Business Opportunities
Corporate
Customer Service
Entrepreneurship
Ethics
Franchise
Fundraising
Home Business
Human Resources
Industrial
International Business
Leadership
Management
Negotiation
Networking
Non Profit Organizations
Online Business
Organizational
Outsourcing
Presentation
Project Management
Public Company
Public Relations
Sales
Six Sigma
Small Business
Strategic Planning
Team Building
Training

Need Help?
Contact Us
FAQ
Submit Articles
Editorial Guidelines
Blog

Site Links
Recent Articles
Top Authors
Top Articles
Find Articles
Site Map

Webmasters
RSS Builder
RSS
Link to Us

Business Info
Advertising

Use of this web site constitutes acceptance of the Terms Of Use and Privacy Policy | User published content is licensed under a Creative Commons License.
Copyright © 2005-2010 Free Articles by ArticlesBase.com, All rights reserved.

Related Solid Wood Flooring Articles